Four Screen Four Display Automatic Incubator Controller XM-18

Four Screen Four Display Automatic Incubator Controller

 

 

XM-18

SH-100-2

 

 

 

Operation Manual

 

 

 

The automatic multi-function incubator researched and produced by our company uses the more popular microcomputer-based technology (using the latest micro-electronics technology and new components), equiping with the imported digital temperature sensor and France moisture sensitive capacitance humidity sensor, which makes this instrument miniaturization, intelligent, high measurement accuracy. This incubator is stable and reliable, time-saving, labor-saving, and easy-to-use. It is the ideal incubation equipment for propagation of poultry and rare birds and small and medium-sized hatchery.

一、Main Technical Index:

1.Temperature Measuring Range: 0-99℃ 2.Temperature Measurement Accuracy: ±0.1℃ 3.Humidity Measurement Range: 0—99%RH 4.Humidity Accuracy: ±3%RH

  1. Number of signal-output: 7, (over-temperature, temperature control, insufficient temperature, egg left-turning, egg right-turning, humidity control, alarm)
  2. The maximum output load current: temperature control, insufficient temperature ≤ 8A/AC220V, over-temperature, egg left-turning, egg right-turning, humidity control, alarm ≤ 1A / AC220
  3. Number of egg-turning: the maximum record is 999 times. 8.cycle of egg-turning: adjustment of 0 – 999 minutes (the factory default is 120 minutes)
  4. egg-turning time: adjustment from 0 to 999 seconds (the factory default is 65 seconds)
    1. ventilation cycle: from 0 to 999 minutes

(the factory default is 120 minutes) 11.ventilation time: from 0 to 999 seconds (the factory default is 30 seconds)

12.Temperature measurement length: About 2 meters

 

二、Working Condition:

  1. Working Voltage: AC 180V – 240V,50HZ 2.Relative Humidity: less than 85% RH 3.Environment Temperature: -10℃ - 60℃

 

Temperature and humidity settings instance: This method is very simple, as long as you set up both points of temperature and humidity, others will generate automatically. For example, a incubation control room       needs that the temperature is 38 ,

humidity        is 60% RH. During normal working, press   SET   and  lift  your hand, a row of led will

display on the lower side of the controller. If you need to change the temperature value, press      to adjust, till to display the temperature 38 you required. And then pressOK and raise your hand, the led will display on the lower side of the controller. If you need  to  change  the humidity value,  please  press           to adjust untill the required humidity 60% RH shows. And then press the keyOK, the controller will automatically calculate and fill the parameters of temperature and humidity, and finally return to normal working state.

 

 

Arbitrary temperature and humidity settings example (which may change and automatically generate interval, but generally do not use it)

During  normal  operation,  press the key and don’t raise your

 

hand, and then press the key    untill display

and then raise your hand, set up the following

 

parameters:

² Set up over-temperature alarm: led display

as shown in right figure: “P1” is the over-temperature alarm value, the alarm will be given if the temperature reaches this value. If any

change is needed, please press      untill it displays the value

you required. And press OK and then raise your hand to save data, and automatically move into the next parameter setting.

² Set up over-temperature value: led display

as shown in right figure: “P2” is the over-temperature value, the exhaust fan will be started up when the temperature reaches this

 

value. If any change is needed, please press          untill it displays the value you required. And press OK and then raise your hand to save data, and automatically move into the next parameter setting.

² Set up upper limit value of temperature

control: led display as shown in right figure: “P3” is the upper limit  of  temperature  control.  The  heating  will  stop  when  the

temperature reaches this value. If any change is needed, please press      untill it displays the value you required. And press OK and then raise your hand to save data, and automatically move

into the next parameter setting.

² Set up lower limit value of temperature

control: led display as shown in right figure: “P4” is the lower limit of temperature control. The heating will start up when the temperature droppes to this value. If any change is needed, please

press      untill it displays  the value you  required. And press

OK and then raise your hand to save data, and automatically move into the next parameter setting.

² Set up low temperature value: led display as

shown in right figure: “P5” is the low temperature value. The standby heating will start up when the temperature droppes to this

value.  If  any  change  is  needed,  please  press        untill it

displays the value you required. And press OK and then raise your hand to save data, and automatically move into the next parameter setting.

² Set up insufficient-temperature alarm value

led display as shown in right figure: “P6” is the insufficient-temperature alarm value. The alarm will be given if the

temperature droppes to this value. If any change is needed, please press      untill it displays the value you required. And press OK and then raise your hand to save data, and automatically move

into the next parameter setting.

 

² Set up over-humidity alarm: led display as

shown in right figure: “P7” is the over-humidity alarm value. The

alarm will be given if the humidity reaches this value. If any change is needed, please press      untill it displays the value you required. And press OK and then raise your hand to save  data,

and automatically move into the next parameter setting.

² Set up upper limit value of humidity control

led display as shown in right figure: “P8” is the upper limit value of  humidity  control.  The  humidification  will  stop  when  the

humidity reaches this value. If any change is needed, please press     untill it displays the value you required. And press OK and

then raise your hand to save data, and automatically move into the next parameter setting.

² Set up lower limit value of humidity control:

led display as shown in right figure: “P9” is the lower limit of humidity control. The humidification will start when the humidity

droppes to this value. If any change is needed, please press

untill it displays the value you required. And press OK and then raise your hand to save data, and automatically move into the next parameter setting.

² Set up low humidity alarm value: led

display as shown in right figure: “PP” is the low humidity alarm.

The alarm will be given if the humidity droppes to this value. If any change is needed, please press       untill it displays the value you required. And press OK and then raise your hand to save

data, and automatically move into the next parameter setting.

Set up Low humidity stop humidification : led display as shown in right figure: “Pd” is the

value of Low humidity stop humidification, When the humidity value is lower than this value, the humidification will stop. If any change is needed, please press      untill it displays the value you required, and press OK and then raise your hand to return to the normal working state.

 

Egg-turning and calibration parameter setting

 

During normal operation, press the key and don’t raise

 

your hand, and then press the key till display

and then raise your hand, set up the following parameters:

Set up egg-turning

 

interval: as shown: “F1″ is two successive egg-turning interval

 

 

(unit: minute), if any change is nedded, please press untill it displays the value you required. And press

 

 

and then

 

lift your hand to save data, and automatically move to the next

 

parameter setting.

² Set up egg-turning time: led display as

shown in right figure: “F2″ is the egg-turning time (unit: second), which represents the time of turning eggs, if any change is necessary, please press       untill it displays the number you

required. And press OK and then lift your hand to save data, and automatically move to the next parameter setting.

² Set up ventilation interval: led display as

shown in right figure: “F3” is the ventilation interval time (unit: minute), if any change is needed, please press              untill it displays the value you required. And press OK and then raise your

hand to save data, and automatically move into the next parameter setting.

² Set up ventilation time: led display as shown

in right figure: “F4” is the ventilation time (unit: second), if any change is needed, please press      untill it displays the value you required. And press OK and then raise your hand to save data,

and automatically move into the next parameter setting.

² Set up temperature calibration: led

display as shown in right figure: “F5” is the  temperature calibration value, this parameter may revise the temperature

 

deviation brought about by improper selection of temperature measuring point. If any change is needed, please press         untill it displays the value you required. And press OK and then

raise your hand to save data, and automatically move into the next parameter setting.

² Set up humidity calibration: led display as

shown in right figure: “F6” is the humidity calibration, this parameter may amend the humidity deviation caused by improper selection of humidity measuring point. If any change is needed,

please press      untill it displays the value you required.  And

press OK and then raise your hand to save data, and automatically move into the next parameter setting.

² ☆ Number of egg-turning: led display as

shown in right figure: “F7” is the number of egg-turning, press the key OK and then raise your hand to move into the next parameter setting.

² ☆ Number of brightness: led display as

shown in right figure: “F8” is the brightness of LED, If any change is needed, please press            untill it displays the value you required. And press OK and then raise your hand to save data, and

automatically move into the next parameter setting.

 

Time of Alarm Elimination: led display as

shown in right figure: “F9” is the Time of Alarm Elimination(unit:

minute), If any change is needed, please press            untill it displays the value you required, and press OK and then raise your hand to return to the normal working state.

 

Egg-turning and Silencing Description

 

² Egg-turning Mode:

Automatic egg-turning:

Turn eggs automatically in accordance with the set egg-turning interval  and  egg-turing  time,  turn  left  →  interval  →  turn  right

→interval → turn left … … alternation of egg-turning. The number

 

of egg-turning will display on the parameter F7, and will be zero if the controller power is cut off. In order to ensure normal egg-turing, please switch to the state of automatic egg-turing.

Manual egg-turning:

Press the key       and do not lift your hand, the controller will enter into the state of manual egg-turing after2 seconds. You’re your hand when it is adjusted to the desired location, the controller will get into the state of automatic egg-turing.

The computer wil define automatically the direction of egg-turning.

² Silencing function: when the controller give an alarm, press the  key    and lift your hand, to remove the buzzer sound and alarm output, but then the alarm indicator lamp still lights up; press the

key         again and raise your hand, to restore buzzer sound and alarm output control.

 

七、Restore Factory Settings

 

Press both keys of           at the same time for more than three seconds, the controller will display zero. Raise hand immediately

after hearing “Di” from the buzzer, the controller will automatically restore the factory settings.

Factory Settings:

Reference temperature: 38.0 ; reference humidity: 60% RH; cycle of egg-turning: 120-minute; time of egg-turning:65 seconds; ventilation cycle: 120 minutes; ventilation time: 30 seconds; egg-turning state: automatic egg-turning

 

八、Controller Wiring Diagram:

 

 

 

Dear Users:

Hello!

Welcome to use our automatic incubator by computer! Please pay attention to the following aspects in use:

  1. The micro-computer controller has been made adjustment for temperature, humidity, egg-turing, exhaust, etc. before leaving factory, which meets settings required by incubation. Under  normal circumstances, you do not need to set up and may use it by connecting the power supply. Factory settings: temperature 38 , humidity 60% RH; cycle of egg-turning: 90-minute, time of egg-turning: 180 seconds; ventilation cycle: 120 minutes; ventilation time: 30 seconds; egg-turning state: automatic egg-turning.
  2. If you need only to change the temperature and humidity parameters, please refer to Section III in page 2 of this Manual. Please do not set up other parameters in order to avoid operation errors which may affect your usage and bring you f unnecessary losses.
  3. Temperature and humidity sensors are made of high precise and micro-molecular materials, please do not make the sensor come into contact with the water directly. The dust must be regularly cleared on the surface of the sensor, or it will affect the measurement accuracy.
  4. The manufacturer should only assume the obligation for products selled to users, but not undertake users’ other losses caused by product failure.

Post time: Aug-17-2021